A customer had me out to remove a dead pine tree, broken & hung-up, that was in danger of collapsing onto his home. That worked completed, he had me back out a week later to buck up all of the fallen wood on his property.
Log bucking is simply cutting wood into shorter lengths that can later be split for firewood or used in outdoor fire pits. Generally the lengths are from 12 to 16 inches, depending. I don’t do splitting. I do stack, but the customer didn’t want that in this case.
Thanks to the more powerful equipment I use and the tools I have for handling timber I was able to cut up everything on his lot in 2.5 hours. In all I bucked Oak ranging from 6 to 12 inches in diameter, Pine from 4 to 16 inches, and large Tulip Poplar up to 22 inches that had fallen in a storm. When you have many fallen trees and a small chainsaw, it can save you many, many hours to use the log bucking service I offer.
The oak was dead. 45 feet tall, 11 inches wide, leaves and bark all. Before Hurricane Matthew came through NC, I received a call to take this dead oak down in its fenced-in yard. Get it down under control, not under the heavy winds and rain of Matthew.
Tree & Yard
The homeowner advised there was one corner of the yard where the tree would fit, correctly so. In addition, the yard was well gardened with flower beds and plenty of hardscape – overall a beautiful yard you don’t want to damage. Moving blankets protected the pavers, a tarp the fence.
Target Area
Why was the tree dead? Lightning was one possibility as the tree seemed to suddenly die. Lightning strikes can go without visual damage for seasons, too, so when it happened was hard to say. When I dug around the base of the oak to inspect the root collar, I dug over 8 inches and still didn’t reach the roots. Suffocation may have killed this oak as tree roots need oxygen too. Construction is often the cause even though years pass before the tree suddenly dies.
Dead TopDead Bark
I sounded the tree with a 3 lb. hammer. Dry but solid. The outer phloem was completely dead, the leaves totally dry.
I used a rope to control the oak with a rope puller, then the usual notch, back-cut, and wedges. Look at the stump and you can see two patterns on the back-cut, the obscured portion with a dull chain, and the clear portion a sharp one.
Stump – Dull vs Sharp Chain
The tree landed right on the spot. The homeowner chose “downing” only, so I cut up and stacked the oak into a few portions and cleaned up. No damage to the hardscape and minimal damage to the tender salvias and torenias around the base of tree. The wood was dead heavy, each section 100 pounds easy. Only the top fifteen feet were completely rotten.
Tree Down 1 of 3Tree Down 2 of 3Tree Down 3 of 3Cleanup 1 of 3Cleanup 2 of 3Cleanup 3 of 3
I encountered a large, very dead oak tree when a man I ran into on another job called me out to his home. He said when I met him that someone walking the neighborhood looking for tree work had passed on it. I visited in person after he sent a picture that showed a favorable crotch for a rope.
The dead, rotten oak in question.
The tree was about 60 feet tall, 20-22 inches in diameter, full of dead wood up top, and rotten bark all the way to the roots. Even the root flare was rotting. There was some firmer wood inside. It had a favorable lean into a clearing backed by strong trees that could hold a rope. I told the man that if he wanted a precision job, bring in a cherry picker to bring it down piece-by-piece; I didn’t think anyone would climb this tree.
After my visit I sent a quote. I described what I would do: put a rope on the tree about 30 feet up and use a rope puller. I wanted the entire tree to come over like it was blown down. I gave three prices: lowest if it came down on one pull, middle if it required multiple pulls, and highest if I had to cut it down. I also asked him to be present with his own chain saw in case things went wrong. And a dead, rotten tree can go very wrong. I could be hit by falling branches, a collapsing shell, a trunk broken mid-point, or even the entire tree falling over.
I didn’t hear back from the man.
That is until a month later, when he asked me to come out and do the work that Wednesday. It had rained recently and I thought the conditions favorable for pulling the tree over. I was shocked when I arrived and found a new shed built in the exact spot where I had planned on felling the tree!
I went over options with the man. There was a good spot about 90 degrees from the lean. He assured me multiple times that, because the shed was free and although he didn’t want the shed hit by the tree, it was okay if the tree did hit it. He wanted that dead, rotten tree down. He also said the same thing about any ornamental trees, shrubs, or other plants. All damage in that area was waived.
I set up the area. Coned off a restricted area, got my rope in place, and got all my equipment out. In the video, you can see I didn’t use a running bowline to set the rope on the crotch. Instead, I ran the rope down to the base of the tree and attached it with a timber hitch. I wanted to get my rope back for another plan if things didn’t go well. I also used a zepplin bend on two ropes to get the length I needed.
Rope set up on the oak for pulling.Rope puller set up with slings on a strong tree.
Story short. The tree would not go over with the puller alone. I had to cut. I gave a hand signal to the man so he could tell me if he saw the tree moving and I made my notch while looking up as often as possible. On the back cut I noticed one side cut much easier than the other. I ignored this clue at the time because I wanted to clear the tree as soon as possible.
Back on the rope puller, the tree came over. It landed perfectly, not hitting the shed at all. In fact, the only thing it hit was another tree the man will remove later.
The tree on the ground. A perfect landing.The canopy was rotten through. This is a dangerous situation.
But it didn’t go as planned and I don’t like that. Two things showed why the tree fell it as it did. First, I wanted the tree to land 90 degree from the lean. Second, I noticed one side cutting more easily than the other. The result was the tree landed at 45 degrees from the intended lay. Jeff Jepson in “To Fell A Tree” states that trees felled perpendicular to the lean often result “…in a tree landing 45 degrees away from the intended lay.” One reason is “hinge wood [that] could not support the tree (weak, decayed)…” You can see that almost 50% of the hinge has either rotted away or is decayed, punky wood. This was the side that cut more easily.
The hinge of the tree had good wood, no wood, and rotten wood.The clue that the internal wood may be defective as well.
The tree was felled safely. The only way to get better odds on property damage would have been to use a bucket truck and that would have been 3 to 4 times more expensive. I laid out the facts for the man and he decided. That is how I treat my customers.
